Ford Bronco lug nut torque

Ford Bronco owner’s manuals give 100 lb-ft (135 N·m) for 2021, 2022–2026 (Non-Raptor) and 150 lb-ft (204 N·m) for 2022–2026 (Raptor). Check which applies to yours. Tighten them in a star pattern with a torque wrench.

Sources checked

Wheel nut torque, 2021, 2022–2026 (Non-Raptor)

100lb-ft135N·m

04080120050100150ft-lbN·m
As printed
“M12 X 1.5: 100 lb.ft (135 Nm)”
Stud thread
M12 x 1.5
Source
2026 Bronco Owner's Manual (Ford): Wheel Nuts - Excluding: Raptor

Ford Bronco lug nut torque by model year

Model yearVersionTorqueManual page
2026Non-Raptor100 lb-ft (135 N·m)Wheel Nuts - Excluding: Raptor
2026Raptor150 lb-ft (204 N·m)Wheel Nuts - Raptor
2025Non-Raptor100 lb-ft (135 N·m)Wheel Nuts - Excluding: Raptor
2025Raptor150 lb-ft (204 N·m)Wheel Nuts - Raptor
2024Non-Raptor100 lb-ft (135 N·m)Wheel Nuts - Excluding: Raptor
2024Raptor150 lb-ft (204 N·m)Wheel Nuts - Raptor
2023Non-Raptor100 lb-ft (135 N·m)Wheel Nuts - Excluding: Raptor
2023Raptor150 lb-ft (204 N·m)Wheel Nuts - Raptor
2022Non-Raptor100 lb-ft (135 N·m)Wheel Nuts - Excluding: Raptor
2022Raptor150 lb-ft (204 N·m)Wheel Nuts - Raptor
2021All100 lb-ft (135 N·m)Wheel Nuts

Read on Ford’s own site on October 14, 2026. Years not listed haven’t been checked yet, or their manual prints no value; check your own manual.

How to tighten them

  1. Clean any dirt or rust off the studs, the nuts and the wheel’s mounting face. Don’t oil them unless the manual says to.
  2. Thread every nut on by hand until it seats against the wheel.
  3. Lower the vehicle so the tire takes its weight, and set a torque wrench to the value for your model year and version in the table above.
  4. Tighten the nuts in a star pattern, going around two or three times, until the wrench clicks on every nut.
  5. Check the torque again after a short drive if your manual says to.

What the Ford manual adds

  • Torque specifications are for nut and bolt threads free of dirt and rust.
  • Retighten the lug nuts to the specified torque within 100 mi (160 km) after any wheel disturbance (such as tire rotation, changing a flat tire, wheel removal).
  • Retighten the lug nuts to the specified torque within 100 mi (160 km) after any wheel disturbance, such as tire rotation, changing a flat tire or wheel removal.

More detail, including how many passes to make: how to torque lug nuts. Setting and using the wrench: how to use a click torque wrench. Nuts or bolts, car by car: lug nuts vs wheel bolts.

Other Ford models

Questions

What is the lug nut torque on a Ford Bronco?

100 lb-ft (135 N·m) for 2021, 2022–2026 (Non-Raptor); 150 lb-ft (204 N·m) for 2022–2026 (Raptor), as printed in Ford’s owner’s manuals (2021–2026).

Can I use an impact wrench?

Not to finish. An impact wrench can’t set a torque and easily overshoots it, which stretches studs. Run the nuts down by hand or lightly, then finish with a torque wrench in a star pattern.

Should I oil the studs?

Not unless the manual says so. Torque values assume clean, dry threads; oil lets the same torque stretch the stud further. Some manuals, Kia’s and Mazda’s among them, say to keep oil and grease off wheel nuts and bolts altogether.