Ram 2500 lug nut torque
Ram 2500 owner’s manuals give 130 lb-ft (176 N·m) for 2012–2026 (Cone nuts), 134–149 lb-ft (182–202 N·m) for 2024–2026 (Dual rear wheels), 129 lb-ft (175 N·m) for 2012–2026 (Flanged nuts) and 135 lb-ft (183 N·m) for 2010–2011. Check which applies to yours. Tighten them in a star pattern with a torque wrench.
Sources checked
Wheel nut torque, 2012–2026 (Cone nuts)
130lb-ft176N·m
- As printed
- “SRW 130 ft-lb (176 N·m) Cone M14 x 1.50 22 mm”
- Stud thread
- M14 x 1.50, M14 x 1.5
- Socket
- 22 mm
Ram 2500 lug nut torque by model year
Read on Ram’s own site between October 14, 2026 and October 22, 2026. Years not listed haven’t been checked yet, or their manual prints no value; check your own manual.
How to tighten them
- Clean any dirt or rust off the studs, the nuts and the wheel’s mounting face. Don’t oil them unless the manual says to.
- Thread every nut on by hand until it seats against the wheel.
- Lower the vehicle so the tire takes its weight, and set a torque wrench to the value for your model year and version in the table above.
- Tighten the nuts in a star pattern, going around two or three times, until the wrench clicks on every nut.
- Check the torque again after a short drive if your manual says to.
What the Ram manual adds
- Use only authorized dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.
- Do not oil wheel studs.
- NOTE: Dual wheels are flat mounted, center piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts at the interface between the lug nut/bolt and the washer.
- Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice.
- After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly tightened.
- After 25 miles (40 km), check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel.
- Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts at the interface between the hex and the washer.
- Using the wheel wrench, finish tightening the wheel nuts using a crisscross pattern.
- If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station.
More detail, including how many passes to make: how to torque lug nuts. Setting and using the wrench: how to use a click torque wrench. Nuts or bolts, car by car: lug nuts vs wheel bolts.
Other Ram models
- Ram 1500129 or 130 lb-ft, by year and version, 2010–2018, 2020–2027
- Ram 1500 Classic130 lb-ft (176 N·m), 2019, 2021–2024
- Ram 3500129, 130, 134–149, 135 or 145 lb-ft, by version, 2010–2026
- Ram Dakota120–160 lb-ft (163–217 N·m), 2010–2011
- Ram ProMaster145 or 146 lb-ft, by model year, 2014–2027
- Ram ProMaster City63 or 89 lb-ft, by version, 2015–2022
Questions
What is the lug nut torque on a Ram 2500?
130 lb-ft (176 N·m) for 2012–2026 (Cone nuts); 134–149 lb-ft (182–202 N·m) for 2024–2026 (Dual rear wheels); 129 lb-ft (175 N·m) for 2012–2026 (Flanged nuts); 135 lb-ft (183 N·m) for 2010–2011, as printed in Ram’s owner’s manuals (2010–2026).
Can I use an impact wrench?
Not to finish. An impact wrench can’t set a torque and easily overshoots it, which stretches studs. Run the nuts down by hand or lightly, then finish with a torque wrench in a star pattern.
Should I oil the studs?
Not unless the manual says so. Torque values assume clean, dry threads; oil lets the same torque stretch the stud further. Some manuals, Kia’s and Mazda’s among them, say to keep oil and grease off wheel nuts and bolts altogether.